Easy Way to Build Steps Off Back Porch

Download Article

Download Article

Once carpenters were judged by how skilled they were by the projects they had worked on, the tools in their tool boxes and by their ability to build steps. Despite the skill level, building porch steps is still within the capabilities of the average do-it-yourselfer.

1. 1

   Calculate the run of the steps (how long they will be). Also, check local codes for specifications regarding handrail requirements and permitting.^[2]

2. 2

   Measure from the bottom of the level to the ground using a 4-foot (1.2 m) level set on the top of the porch.

   • Take the total height and divide it by the height of the riser. This tells you the number of steps you will need.
   • Remember that the riser height averages between 6 and 8 inches (15.2 to 20.3 cm) high. As an example, a height of 35 inches (88.9 cm) divided by a 7-inch (17.8 cm) riser will result in 5 equal steps.
   • Don't forget to consider the blocking or apron at the bottom of the stairs to support the stairs.

3. 3

   Multiply 5 steps by 10.5 inches (26.7 cm). That will give you the run (or length) of steps from the face of the porch to the end of the steps. In this case, the run is 52.5 inches (1.33 m).

4. 4

   Lay out the steps to be cut from the stringer using a carpenter's square. ^[3]

   • Have the square set up by clamping a straight edge at the 7-inch (17.8 cm) mark on the short outside section of the square.
   • The long outside section of the square, at that point, will be at the 10.5-inch (26.7 cm) mark.

5. 5

   Place the square along the edge of the stringer and mark out the 5 steps beginning at the end.

6. 6

   Use a circular saw to cut out the steps and square up the ends of the stringer to the steps. Double check all of your measurements carefully and make sure they are clearly visible, and then use the saw. Note that you will not cut all the way through with the circular saw. Finish the cut with a hand saw or jigsaw.

7. 7

   Take the first stringer you cut out and use it as a pattern. Now, mark out the other stringers you need.^[4] The spacing of the stringers should not be more than 16-inches (40.6 cm) apart for strength. You would need 4 stringers on a 4-foot-wide (1.2 m) stair.

8. 8

   Attach the stringers to the porch using metal stringer hangers and 1.5-inch (3.8 cm) deck screws. ^[5]

   • Check to make sure that they are plumb and level to each other as you go.
   • The bottoms of the stringers need to be sitting on a concrete pad or brick base and not on bare ground.

9. 9

   Connect the riser board (cut to the length and width needed) using 2.5-inch (6.4 cm) deck screws.

10. 10

    Install the 2 x 6-inch (5.1 X 15.2 cm) treads (again cut to length) parallel to each other with 1/8 inch (3 mm) spacing between the boards.

11. 11

    Attach the treads to the stringers using 2.5-inch (6.4 cm) deck screws. ^[6]

12. 12

    Finish it with waterproof deck stain or exterior porch paint.

Advertisement

Add New Question

• Question

  Can I buy a pre-cut kit?

  

  Yes, most big-box hardware stores carry these.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

• Always use treated lumber for your stringers and treads and cedar for the riser.

• You may need to add extra height to each riser if the ground around the porch slopes away. To get the amount you need, use a level and a long straight edge. Place one end on the porch floor and measure out from the edge to the end of the run. Now, measure down to the ground. Divide this number by the number of steps. Use that number for the height of the riser.

• You may find it necessary to drill pilot holes to keep from spitting the wood when screwing them down.

Advertisement

• Always use a dust mask and safety glasses when cutting treated wood.^[7]

Advertisement

Things You'll Need

• 4 foot (1.2 m) level
• Tape measure
• Electric or battery operated drill
• 1/8 inch (3 mm) drill bit for pilot holes
• Hammer
• Circular saw
• Hand saw or jigsaw
• Carpenter's square
• Spring clamps
• Metal or wooden yardstick for a straight edge
• 1.5 inch (3.8 cm) deck screws
• 2.5 inch (6.4 cm) deck screws
• Concrete drill bit
• 2 inch (5.2 cm) Concrete nails
• 2 x 12 inch (5.1 x 30.5 cm) treated lumber for stringers
• 2 x 6 inch (5.2 x 15.3 cm) treated lumber for treads
• 1 x 6 or 1 x 8 inch (2.5 x 15.2 or 2.5 x 20.32 cm) cedar boards for risers and/or toe boards
• Waterproof deck stain or porch enamel
• Concrete blocks

About This Article

Article Summary X

If you want to build porch steps, measure from the top of the porch to the ground, then take the total height and divide it by the riser, which is usually between 6 and 8 inches. For example, divide 35 inches by a 7 inch riser to get 5 steps. Next, mark the steps on your stringers, cut out the steps with a saw, and attach the stringers to your porch. Connect the riser boards and treads, then finish your steps with a waterproof deck stain. To find out more about the parts of a set of steps, including what the run and stringers are, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 457,587 times.

Did this article help you?

weatherlytheinder1989.blogspot.com

Source: https://www.wikihow.com/Build-Porch-Steps

Share this post